Motorized Pan Tilt Heads,Manual for the PT 3000c Pan/Tilt head Motor.

SAFETY PRECAUTIONS

CAUTION: Risk of Electric shock. Do not open.
CAUTION:To reduce the risk of electrical shock. Do not open covers.
No user serviceable parts inside. Refer servicing to qualified service personnel.

GRAPHIC SYMBOLS EXPLANATION:

The lighting flash with a arrowhead symbol, in an equilateral triangle, is intended to alert the user. There is un-insulated"dangerous voltage" presence near the product's enclosure which may be a risk to people.

The exclamation point within an equilateral triangle is to alert the user to reference of the important operating and maintenance (servicing) instructions.

Page A

INDEX

1.0 Important Safeguards Page 1.

2.0 Summarize Page 1.

3.0 Pan Tilt Setup Page 2.
3.1 Addressing setting of Pan Tilt Page 2.
3.2 Setting of terminal resistance Page 3.
3.3 Setting of communication protocol Page 3.
3.4 Setting of baud rate Page 4.

4.0 Connection Details Page 4.
4.1 Connection Pan Tilt with controller. Page 5
4.2 Connection Pan Tilt with outdoor housing Page 5
4.3 Control wiper Page 6

5.0 Setting Pan and Tilt End Page 6
5.1 Setting the Pan limits Page 6
5.2 Setting the Tilt limits Page 6

6.0 Installation Page 6

7.0 Specifications. Page 7

Page B

1.0 IMPORTANT SAFEGUARDS:
a) This apparatus must be connected to earth. This installation should be made by a qualified installer.
b) Do not carry out electrical installations in wet weather conditions
c) Voltage must be matched with Pan Tilt.
d) Examining connection,to be sure that it is correct.
e)Please not to put the pan tilt with auto scanning continuously for long time.

2.0 SUMMARY
This unit is a hi-tech CCTV product which incorporates panoramic speed-variable PAN Tilt, multifunctional decoder, CPU processor, memory chip into a whole. It can largely reduce connection and installation processed of components in the system, rise up reliability of the system and facilitate installation and maintenance. Therefore it has advantages of beautiful appearance, compact structure and easy operation.

2.1 Integrated Multi-protocol Decoder:
a)With integrated decoder and Multi-protocol, it can integrate 16 kinds of communication protocols in maximum. As its baud rate of communication can be adjusted, it is compatible with many normal systems by easy setup inside the done camera, so it has stronger versatility.
b) RS485 serial control: addresses of unit 1-511.

2.2 Integrated Speed-Variable Pan and Tilt:
a) Turning 0-355 horizontally and an adjustable speed from 0.25 to 10 degrees per second; turning -90 -+20 vertically with a speed up to 10 degrees per second.
b) Running stable at low speed with super lower noise. Pictures have no shaking.

2.3 High Intelligent Degree:
a) As much as 64 present positions can be preset with powerless memory.
b) The pan tilt can scan horizontally between two points and scan speed can be modified.
c) Six sets of programmable tour locus with 16 positions each set. The running speed and the detention time are adjustable respectively:

2.4 Could to be cooperate with outdoor housing, also could control camera that is in housing, also could control camera that is in housing.
a) Camera's iris, focus, zoom could to be manual controlled.
b) Control auto iris shutter speed.
c) Auto white balance tracking.

Page 1

3.0 PAN TILT SETUP;

3.1 Address set
SW1 is used to set address of the pan tilt from 1-511. The ID-CODE from DIP-9 to DIP-1 are equivalent to a 9 bit binary digit. DIP-9 is MSB while DIP-1 is LSB. The state "ON" of each bit means 1, while "OFF" means 0.

Page 2

3.2 Selection of the Terminal Resistor:
As shown in figure 1, DIP 10 of the ID-CODE is the select switch of the 120 terminal resistor on the bus RS485, on which only one terminal resistor of the dome camera at the farthest end can be connected, while the terminal resistors of other devices should be opened.

3.3 Setup of the Protocol and the Default Baud Rate:
As shown in Figure 1, SW2 is used to set the protocol of communication and the baud rate used by the dome camera. DIP-4 to DIP-1 of SW2 is used to select protocols and 16 different protocols can be selected in maximum. Following table shows states of coding switches of protocols selected by the dome camera in which means the protocol has be integrated while means the protocol is temporarily vacant.

Page 3

Some protocols and the states of the coding switches of normal baud rate of the protocols are shown as follows:

3.4 Setup of the Baud Rate of Communication:
As shown in Figure 1, SW2 is used to set the protocol of communication and the baud rate used by the dome camera. DIP-6 and DIP-5 of SW2 are aside to select the baud rate of communication and 4 different baud rates can be selected in maximum. If the controller adopts nonstandard baud rate, you can adjust it to be identical with that of the controller as per the following table.

4.0 CONNECTION DETAILS:
Notice: Before carrying out any electrical installation ensure that the cable being used is at the correct voltage and current rating for the application.

Page 4

4.1 Connecting Pan Tilt with the Controller:
RS485 control signal, power supply (AC 24V) and video signal connect with the controller with a weather proof connector plug (D1). Figure 4's connection diagram is D1. Figure 3 is the cable that is soldered to the weather proof connector.

4.2 Connection of Pan Tilt and outdoor housing:
When collocate the special decoder for housing, decoder's control signal input. Power supply (AC 24V) and video signal output by weather proof connector plug (D2) to connect. Figure 5 is connected way of D2. Note: Connect Pan Tilt's Ground with lens decoder's Ground Furthermore P/T's TXD, RXD must cross connect with lens decoder's TXD, RXD. Otherwise, lens will not to be controlled. Otherwise, could not to preset lens's position, only just could preset pan tilt position.

Page 5

4.3 Control wiper:
Use command (D-ZOOM ON ) to startup wiper; Use command (D-ZOOM OFF) to stop wiper. Also could use call NO. 64 preset position to startup of stop (switch control) wiper.

5.0 SETTING PAN and TILT END

A) Setting the Pan limits (see figure 6): Loosen the M4 screws and loosen the pan strikers. Adjust the strikers until they are at the position to strike the relevant actuator, thus activating the limit switches. Tighten the M4 screws to secure the pan strikers.

B) Setting the Tilt limits (see figure 7): Release the screw locks and adjust the strikers until they are at the position to strike the actuator, thus activating the limit switches.

6.0 INSTALLATION:

A)This outdoor pan tilt unit is intended to be mounted on a wall mount. The unit base has 4 holes equal-spaced on 4" (101.6 mm) P.C.D. See figure 8, which line up with the bracket mounting holes. Mount the unit base onto the bracket using the four M 6 x 25 Hex head screws 6 mm washers and the M6 nuts provided in the packing kit.

B) Remove the six M4 mm fixing screws from the top platform using the three M1/4"-20 screws (supplied). Secure the Sub-plate to the base of the Camera Housing (see figure 1). Secure the sub-b-plate (with camera housing attached) with the six 6 mm fixing screws removed earlier.

Page 6

7. SPECIFICATIONS
Input Voltage: AC 24V
Angular Travel: Pan 350. Tilt +20 -90.
Speed: Pan 0.25-10/second. Tilt 0.25-10/second.
Limit Stop: Externally adjustable
Load Rating 15 KG's (Over The Top MOUNT)
Operating Temperature: -35c-+60c
Construction: Aluminum alloy casting
Measurement: 225(L) x 180 (W)x260(H) (Over The Top MOUNT)
Unit Weight: 10 Kg

Page 7

Pan Tilt Zoom (PTZ) CCTV cameras are affordable and offer better performance then ever.
Pan Tilt Zoom surveillance cameras are used by Government, large corporations, casinos and consumers. Other uses include Mast Aerial Photography.
PTZ cameras rotate horizontally through 360 degrees, vertically through 90 degrees and have motorized optical zoom lenses. A camera turret or motorized swivel is similar to a pan-tilt head.
Pan Tilt movement can be very fast and is controlled through a wired (or wireless) connection, by the mating controller.
PTZ cameras are often mounted in domes, outside dome cameras are weatherproofed, heated and cooled.


Compare three brackets.	PT3000 bracket rear.

PT3000 bracket.	Compare three brackets.

PT3000 bracket.	PT3000 bracket.

Pan tilt enclosure and mounting bracket.	Pan tilt enclosure and mounting bracket.

	Pan tilt enclosure and mounting bracket.


Home Page > Motorized Pan Tilt Heads and Systems > Manual for the PT 3000c Pan/Tilt head Motor.